Showing posts with label Riding tips. Show all posts
Showing posts with label Riding tips. Show all posts

Sunday, March 30, 2008

Perfect Shift Point

Manual transmission is the one to have if you love driving or riding. That's because, manual transmissions allow you to have full control over the engine power delivery, which cannot be asked of an automatic or a CVT.

Engine power delivery is nothing but how much of the engine power goes to the driven wheels. This can be controlled by altering the shifting point of each of the gears of the transmission system.

We'll first see the two extreme cases of shifting with an example: shifting to 5th gear at 20 kph in any vehicle forms one extreme of shifting point. When you do this, transmission snatch occurs. When the clutch is fully engaged and you give full gas, the engine might even stall. This is a scenario of the torque delivery being unable to match the torque requirement. Pressing on to 60 kph in 1st gear is the other extreme of shifting point. Here the engine revs too high and in most cases, even bounces off the rev-limiter.

The optimum shift point lies in between these two cases and that is a bit tricky to find. One must first decide the mode of driving--to conserve fuel or wring maximum performance from the engine. It is depending on this that the optimum shift point is determined. In cars, when a gear too high for the current speed is selected, the whole car will rattle. This can be had as an indication for a bad shifting point. Many drivers do this thinking that it will give good fuel economy. But the truth is, the mileage actually decreases. What actually happens is, the amount of fuel intake increases but with the volume of air sucked in remaining constant. This makes the mixture rich leading to incomplete combustion. This obviously wastes fuel and pollutes the environment.

At the same time, the engine should not be revved too high either. As a thumb rule, for fuel efficient driving, the optimum shift point can be the RPM which is just over half the redline RPM. For performance driving, the gear should be shifted at exactly the RPM where the manufacturer says the engine develops maximum power. This data can be had from the owner's manual.

|Add to Google Reader or HomepageAdd to My Yahoo!Subscribe in NewsGator OnlineAdd to My AOL|

| Add to The Free Dictionary                                                                               |

^IF YOU'RE PASSIONATE ABOUT FORMULA 1, YOU MIGHT ALSO WANT TO HAVE A LOOK AT THIS.

^STAY IN TOUCH WITH WHEELS OF RAM. CLICK HERE. 

Monday, January 14, 2008

Brake Test

The other day I was thinking of learning more about my bike's braking ability--which includes tyre grip levels, feedback from the front brake lever and the handlebar and the bike's overall behaviour under hard braking. I always consider the knowledge of the behaviour of a bike in emergency braking situations to be very important to any rider because, in such demanding situations, when we brake very very hard, we won't be stress-free enough to think about keeping the bike under safe control. Consciously. The control has to come unconsciously. For us to do that unconsciously, we've to simulate the situations and gauge how the bike behaves and how we behave.

I found a nice stretch of tarmac, which was totally fine-sand free and perfectly smooth. I limited myself to 40 kph and made it a point to use the front brake alone. It was a simple test of both my bike's and my ability. I would reach 40 kph, made sure I had no one behind me, and squeeze the front brake lever as hard as I've never done before. Well, what happened then was not too good a feeling. After all, it was trying to spit me into the moon.

I did this several times and learnt a lot of things. The test also taught me that my previous way of braking (read that as the amount of pressure given to the rear brake) wasn't too ideal. I learnt I could use more of the front brake than I thought was safely possible. Until the lessons from this test, my concern with the bike used to be that under very hard braking, the tail used to swing almost 90 degrees to one side (whether left or right depends on the handlebar position). It has happened quite a number of times. I knew the problem was due to the combined effects of relatively low (rear) tyre grip, soft front suspension and a touch too much brake pressure to the rear wheel. I'd been wanting to find a solution for this problem. That's how this test came about.

Since this test, I've been giving more pressure to the front brake than before and it seems to be an improvement. To gauge the full effectiveness of the new find, however, there has to come an emergency situation! I'm not sure I'm looking forward to it!

Links of interest:

> p-force > Chassis? Engine? Brakes? What's the Pick? > The Limit - Found

> Making it "Hush-Hush" > Riding in the Slush > Fuel Efficient Riding

> The Front; the Rear (Part 2) > Brake+Clutch or Brake and then Clutch

> The Front; the Rear > First (long) Ride in Apache 150

Technorati Tags: ,

 

|Add to Google Reader or HomepageAdd to My Yahoo!Subscribe in NewsGator OnlineAdd to My AOL|

| Add to The Free Dictionary                                                                               |

| IF YOU'RE PASSIONATE ABOUT FORMULA 1, YOU MIGHT ALSO WANT TO HAVE A LOOK AT THIS.

| STAY IN TOUCH WITH WHEELS OF RAM. CLICK HERE. 

Monday, November 05, 2007

Riding in the Slush

A week or so before I happened to ride my Apache on rain hit roads that were coated with everything other than black top. On some stretches, I even had to ride through recently dug roads which, mixed with rain water (as they were), would easily prove a match for moto cross circuits! I'm not kidding. It was so worse that I couldn't balance the bike on my feet on those occasions when I had to bring the bike to a complete halt. My shoes were sliding the moment I kept it on the road! Horrible sensation it gave. So, here's what can be done to ride safely in these conditions.
  • If your bike is equipped with a front disc brake, don't use it (unless you have an innate feel for the front end of your bike).
  • Use the rear brakes extremely carefully and only when the bike is absolutely straight - not in the curves. Use the gears judiciously to slow the bike down. If you've got a corner ahead of you, brake super early, bring it down to the lowest gear possible and start turning. And even then, don't lean too much. The front tyres may not grip the road at their best possible level. Remember, they (both the road and the tyres) are coated with all sorts of nonsense.
  • If you have to cross the slush at some speed, say, 30 kph, keep the bike in the appropriate gear and keep the throttle opening constant. Appropriate gear, here, means ensuring that there isn't too much engine power available on tap. For my bike, the appropriate gear is, I believe, 3rd gear. Because, if I keep my bike in 2nd gear and if I happen to open up the throttle, chances are that my rear wheel will start spinning. I may lose control in that situation. As a thumb rule, the higher the capacity of your bike, the higher is the appropriate gear. So, the appropriate gear for my brother's P220 might be 4th gear. Keeping the throttle opening constant is tricky business if you've not got a clean stretch ahead of you. In that case, allow a very safe distance - that will save you from having to reduce or increase the speed - ahead of you. Even if the bloke behind honks like hell, keep cool and avoid accelerating.

And, most importantly, remember to wash your shoes after you reach your destination. In my case, they were in horrible condition by the time I made it to the place!

Friday, September 28, 2007

Fuel efficient riding

High mileage means, maximum kilometers to a liter of fuel - be it diesel or petrol. Maximum kilometers to a liter means, sticking to reasonable speeds of about 50 kph for 100cc bikes and about 80 kph for cars. Why the speed limits? When we stick to those speeds, the engine rotates at a fewer rpm that it does when we travel at 150 kph, for example. And a lower rpm will consume less fuel. So, here’s how I ride my bike when I am in the mood to conserve that last drop of my bike’s diet.

I let the engine idle for about 30 seconds after it starts, for the lube oil to reach all the parts of the engine. This will help cut down friction that which saps mileage.

I keep the engine rpm below around about 4500 rpm, which my engine does when I ride the bike at 50 kph in the top gear.

I crack open the throttle by the millimeter. The opening is so small that even when I depress the clutch while riding, the rpm struggles to shoot above 2500 rpm. Of course, the incredibly torquey nature of my bike’s engine lets me ride the torque wave so well.

I try not to brake at the nth minute that will require me to accelerate again, suddenly, which robs fuel efficiency. When I see the need for braking, I just close the throttle a bit earlier and try and reduce the bike to a safe speed to negotiate. I brake only if it is so demanded.

The front; the rear (Part 2)

This is how I brake in my Apache. The technique holds good for both slow speed city rides and high speed jaunts (above 90 kph).

Step 1: FEEL THE FRONT END - When any vehicle is hauled down, weight transfer pushes the front suspension down. In a two-wheeler they (the front forks) get compressed. Hence, I divide my initial stage of braking in two stages. The first stage, I just feather the front brake lever just to allow the suspension to soak up the initial weight transfer. The bike will not slow down drastically at this stage and this (the feathering action) will be there for a second or two only. Once it stops getting compressed further (after those 1 or 2 seconds), I start squeezing the brake lever even more. The actual pressure with which I grip the front brake depends on the speed at which I travel, whether the surface is smooth or it has bumps/undulations and the grip levels of the tarmac (which is easy to find. I will talk more about it some time later). Dividing my braking into two stages is crucial to my style of riding. If I don't allow the front forks to soak up the initial weight transfer and instead I brake with the actual pressure right from the word go, chances are there that the front wheels will lock up which is not what any one would want!

Step 2: FEEL THE BACK END - As I keep increasing the pressure on the front brakes, the rear end will keep getting lightening up thereby making the rear tyres to lose their contact bit by bit. That's when I will feel the rears starting to slide more and more. That's also the moment when I start to press the rear brake lever too. This helps reduce the rpm of the rear tyres and consequently its sliding action. This gets my rears in line with the fronts keeping the bike deliciously stable under heavy braking action.

Step 3: DON'T FORGET THE ENGINE - I also use engine braking to the max since, it gives me immense control over my bike throughout the braking process. Soon after I've started braking with my rear brakes, I depress the clutch, shift down a gear (say from 5th to 4th), immediately release the clutch lever, then depress it again, shift down a gear again (this time from 4th to 3rd), immediately release the clutch lever all the while keeping the pressure on both the brakes. If necessary, I will keep using this technique until I go down to the 1st gear if the conditions so demand. It was initially very difficult to follow this technique. But, since I firmly believed that engine braking should be used to as much an extent as possible, I kept on trying and finally got the hang of it. You might think that I am making the whole process of braking so complex by introducing engine braking into the context. Believe me, your engine is a very powerful brake when you want it to be. Just try it out and I bet that when you've mastered it, you won't then use your engine to just accelerate.

Happy riding!